Inter loc light on cisco mcs

Advertisement

just replaced a system board on cisco mcs server but it still won't boot. the inter loc light is showing amber, does anyone know what this means?

Advertisement

Hi ,
Try to reseat the RAID controller  i it helps else follow what Terry has said.
http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=migr-5074114
http://public.dhe.ibm.com/systems/support/system_x_pdf/ibm_doc_sraidmr_10i-10.03_user-guide.pdf
regds,
aman

November 30, -0001

Inter loc light on cisco mcs

just replaced a system board on cisco mcs server but it still won't boot. the inter loc light is showing amber, does anyone know what this means?Hi , Try to reseat the RAID controller  i it helps else follow what Terry has said. http://www-947.ibm.co

Cisco MCS or HP Hardware for Unity/CCM

I am looking at purchasing several new Unity servers, and am trying to understand what benefit there is in purchasing the Cisco version. For what reason would I purchase a more expensive Cisco MCS rather than the identical HP? Thanks.Good question, L

Verify physical hard disk drive health MCS 7825-H3 that installed CUCM inside it

Hi Everyone, I have Cisco MCS 7825-3 that installed CUCM ver 6.1.1 inside it. A few days ago the system was crashed and have been recovered. And the symtomp why the system crashed is because corrupted hard disk drive. Now the system is running well.

IBM MCS Server RUnning Unity with NIC Teaming

All, has anyone ever run NIC teaming on and IBM MCS Server with Unity before? At question is the fact that many severs create a virtual MAC address that is different from either of the actual MACs when you team NICs. If this is the case on the IBM Se

Verify physical hard disk drive health MCS 7825-H3

Hi Everyone, I have Cisco MCS 7825-3 that installed CUCM ver 6.1.1 inside it. A few days ago the system was crashed and have been recovered. And the symtomp why the system crashed is because corrupted hard disk drive. Now the system is running well.

Setting Inter VLAN in the Router.

Hi, I trying to set up inter VLAN on the Cisco 2651XM router. I try to type the IP address on the sub interface but it gives me an error. I need to set up first the encapsulation dot1 q. I type encapsulation command but it doesn't recognized. This is

MOH Fixed Audio Source Configuration CCM 4.1

Hy, Can anyone help me with the configuration of MOH Fixed Audio Source? I want to have as MoH a radio brodcasting conected in CCM in LINE-IN (sound card). I have in Control Panel, Sound and Multimedia Properties, Audio Tab, Sound Recording Preferred

MP8 and WebEx

If we need to do only Internal Collaboration using MP8, I understand that we'll need a Web-Ex Node, but would we have to purchase a WebEx contract or incur any WebEx-related monthly charges?Yes. A WebEx Node for Cisco MCS only extends the WebEx cloud

MOH Fixed Audio-Recognizing MOH-USB-Audio on 7835

I am trying to set up a Cisco MOH-USB-Audio card (which is actually a C-Media UTA3100). On a MCS7825 with OS 2000.4.4aSR8 this is no problem.With a MCS7835 and same OS it doesn't work. It displays the card in Hardware-Device manager. But in Control P

BE5K upgrade to 9

Hello.  I have a Business edition 5000 running on a MCS 7828H3.  Its versions are CUCM System version: 6.1.3.1000-16 , and CUC Version 2.1.3ES23.1000-23. Am I to follow the upgrade docs for full CUCM/CUC?  Also, i know there are requirements when usi

Maximum number of IP Phones

Hi everybody. I have installed a Cisco Call Manger 8.6 and I'd want to know how many ip phones can register. Can anybody help me to resolve my doubt? A lot of thanks.Hi there, You will want to have a look at this whole section of the CUCM 8.6 SRND gu

Key board not responding

hi I use a hp 625 laptop my keyboard doesnt want to respond but the wifi and the cap loc light work  regards D M NHlapoHow old is the phone? If it is less than a year old, it's still under the manufacturer's warranty. Take it to a Verizon store and h

Cisco 2950 - 3350 Trunking issue - Port not lighting up

Hi There, I have two switches I am trying to connect a 2950 and a 3350. I have a crossover cable connecting them from fa0/24 to fa0/24 setup as a trunk, however they won't connect and the port on both switches is down, (e.g no port light coming on on

Install Cisco restricted CUCM on MCS that have unrestricted version ?

Dear All , I  installed unrestricted version  on MSC server by mistake and I tried to install a restricted version after it but I failed do it and after check Cisco doc. I read  that  it is not possible to revert back to restricted version once upgra

Release Strategy for inter Storage Loc Material transfer within same Plant

Hi Guru's I hope all are doing good. I gota small concern to share with you. Is it possible to apply Release Strategy between two Storage Locations within same Plant for Material Movement? Many Thanks SONALRelease Strategy cannot be assigned in mater

How many clients support by Cisco One Light Weight AP1262?

Hi Friends, Recently, our company wireless AP 1262 connected more than 40+ clients, and sometimes the wireless access speed is too slow.  those clients are only for MES data transfer, the date no more than 10K of each stations. So I'd like to know if

Blue indicator light on 1131

The ringed indicator light on the 1131 normally glows green. What is indicated when it is glowing blue instead? Is this a power issue?Hi, Please take a look at the below table: Table 3-1     LED Signals Message type Cable Bay Area Top of Unit Meaning

My wireless internet was blocked by CISCO guest access

My internet service was from AT&T and now it was changed to Timer Warner. But one problem appears every 1 or 2 months. After I click SAFARI, the menu shows: CISCO GUEST ACCESS Enter the guest access password to access the internet. Ask the owner if y

IGMP Snooping configuration for Multicasting on Cisco Catalyst 3020

IGMP Snooping configuration for Multicasting on Cisco Catalyst 3020 Hi Guru, Our switch model is "Cisco Catalyst Blade Switch 3020 for HP" We are building HA (High Availability) Databases infrastructure. Currently, there are two nodes(hosts- ser

Cisco UC560 Not Clearing Static Routes When VPN Connections Drop

We have a Cisco UC560 (UC560-FXO-K9) running "Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1)"  The issue is when we have end users connecting with the Cisco VPN Client to this device somet